Fostex FF85WK Speaker Grille (Square) / オリジナルスピーカーグリル（スクエア） 2個セット
Physical (worldwide shipping)
- Ships within 2 daysShips by Anshin-BOOTH-PackPhysical (direct)1,380 JPY
Physical (ship to Japan)
- Ships within 2 daysShips by Anshin-BOOTH-PackPhysical (direct)1,380 JPY
Fostex FF85WK用のオリジナルスピーカーグリル（スクエア（スピーカーユニットと同形状））です。 左右のスピーカー用に、2個セット（1ペア）でお届けします。 ※スピーカーユニット本体や取付用のネジは含まれません。 🌐English description below ↓
製品の特長・スペック
- ネジ穴ピッチは対角で約86mm（±1mm程度の余裕あり）で設計し、FF85WKでの装着を確認しています。 - ユニット前面のリング状の段差に干渉せずに、スペーサーを使わずにフレームに直接ねじ止め可能な構造です。 - グリルの外形は、4隅の対角サイズは実機に合わせた約100mmですが、縦横幅はユニットのΦ83mmに対してΦ85.5mmとわずかに外側へはみ出した形状です。 - メッシュ部は音抜けを最優先し0.8mm厚のドーム形状に仕上げています。指で強く押すと適度なしなりがある設計です。 - 反射を抑えたマット仕上げです。
仕上がりについて
商品は3Dプリンターによる自作品です。滑らかな仕上がりになるよう造形設定等工夫していますが、積層痕や微小なムラ・個体差があります。工業製品並みの完璧さをお求めの方はご購入をお控えください。
🌐 English
Fostex FF85WK — Custom Speaker Grille (Square) / Set of 2 A custom-designed grille to protect and dress up your Fostex FF85WK full-range driver. This square version is shaped to the driver's outline for a built-in look. Fine honeycomb mesh with a gently domed profile, made to look at home on a finished build. Shipped as a set of 2 (one pair, for the left and right speakers). Please note: the speaker driver and mounting screws are not included.
Features & Specs
- Outer dimensions: approx. 85.5 mm across the flats and approx. 100 mm across the diagonal (corner to corner). The diagonal is sized to the driver's frame and stays within it; the flats extend just slightly beyond the driver body (Ø83 mm). - Designed around a diagonal mounting-hole pitch of approx. 86 mm (±1 mm tolerance); fit is confirmed on the FF85WK. - Mounts directly to the frame — no spacer required. The design clears the raised ring on the front of the driver. - The mesh has a 0.8 mm domed profile for maximum acoustic transparency. By design it flexes slightly under firm finger pressure (it is a light cover, not a rigid guard) and does not deflect anywhere near the cone. - Matte, low-reflection finish.
About the finish
Each piece is FDM 3D-printed in PLA and finished by hand. I tune the print settings for a smooth result, but faint layer lines and small piece-to-piece variation are part of its handmade character. If you need mass-production-level perfection, please consider this before ordering.
For overseas buyers
This item can be ordered from outside Japan using the Buyee cart shown on this page. Feel free to message me with any questions about fit or shipping.