NAVY TOWBAR_アメリカ海軍艦上牽引バー
- 1/72 TOWBAR_2個セット¥ 1,500
- 1/48 TOWBAR¥ 1,400
- 1/32 TOWBAR¥ 1,700
アメリカ海軍の空母等で艦載機を牽引する為に使用されているバーの1/72・1/48・1/32スケールの3Dプリントモデルです。(1/72は2個セット、他は1個入りです。) 1/72はV1MODELSさんの米海軍デッキトラクターというモデルがありますので併せてご利用することをお勧め致します。 そちらは下記のリンクからお買い求めください。 https://booth.pm/ja/items/4784428 ◇本体は組み立て式ですので発送通知で送られたメッセージにあるURLから組み立て説明のPDFをご覧になって製作してください。 ◇ 本商品にはデカールシールと鎖が付属します。(超精細になる為1/72に鎖は付属しませんので再現されたい場合にはお好みのサイズの鎖をご用意ください。) ◇1/48と1/32に関して。必要ならば回転軸の補強で真鍮等の金属線を組み立て説明書を参考に組み込んでください。(直径0.5mm,0.8mm) ◇1/32に関して、組み立てを容易にする為に本体と一体で出力した丸い取手のパーツがあるのですが、出力品の中には微妙に造形が甘い場合がありますので、念の為に予備パーツを付属していますので気になる場合はお手数ですが、当該部分を差し替えてください。 ◇細部のディテールまでモデリングしましたが、艦載機の前脚に取り付ける場合はご自分の模型に合わせて調整してご使用ください。 ◇高精細な4Kの3Dプリンターで出力されていますが一部積層痕はございますので、ヤスリで処理してください。 ◇パッケージ 生産・発送をよりスムーズにする為、商品の説明書は同封せず、必要と思われる商品にはpdf形式で説明書を用意致しましたのでパソコンもしくはスマートフォンで閲覧・ダウンロードやプリントアウトしてご利用ください。(発送通知にURLを添付致します。) ※注意事項 ・パーツが輸送の際にサポート材から外れることもないとは言えませんが、サポート部分の欠損・変形は返品の対象にはなりませんのでご了承ください。 ・商品のレジン色は材料調達の関係上予告なく変更することがございます。 ・商品は写真や資料等から3Dモデリングしていますので、実際の牽引バーとは細部の寸法とは多少異なる場合があることをご理解の上お買い上げください。 ・商品内容は予告なく改修される場合がございます。 ・レジン製ですのでプラスチック用接着剤ではなく、瞬間接着剤などをご使用ください。 ・各パーツはラフトと呼ばれる土台からサポート材(ランナーのようなもの)が繋がってパーツを支えていますので、パーツごとにラフトとサポートを大まかに切り離し、その後ニッパーやデザインナイフで慎重にサポートを切り離して整面して組み立ててください。 通常発送まで5日以内ですが、予約商品同時購入の際は予約商品の発送と併せて発送いたします。よろしくお願いします。 This is a 1/72, 1/48 and 1/32 scale 3D printed model of the bar used to tow aircraft on US Navy aircraft carriers. (1/72 is a set of 2, others are 1 piece.) There is a 1/72 model called the US Navy deck tractor by V1MODELS, so we recommend using it together. Please purchase them from the link below. https://booth.pm/ja/items/4784428 ◇The main body is assembled, so please refer to the PDF of the assembly instructions from the URL in the message sent in the shipping notification. ◇ This product comes with a decal sticker and a chain. (The 1/72 model does not come with a chain because it is super detailed, so if you want to reproduce it, please prepare a chain of your preferred size.) ◇ Regarding 1/48 and 1/32. If necessary, please refer to the assembly manual and incorporate metal wires such as brass to reinforce the rotating shaft. (Diameter 0.5mm, 0.8mm) ◇ For 1/32 scale, there is a round handle part that is integrated with the main body to make it easier to assemble. Parts are included, so if you are concerned, please replace the relevant part. ◇I have modeled every detail, but please adjust it according to your model when attaching it to the front landing gear of a carrier-based aircraft. ◇Although it was printed with a high-definition 4K 3D printer, there are some layer marks, so please sand them down. ◇ Package In order to make production and shipping smoother, we do not enclose product manuals, and we have prepared manuals in pdf format for products that we think are necessary. Please use it. (The URL will be attached to the shipping notification.) ※Notes ・Although we cannot guarantee that the parts will come off from the support material during transportation, please note that damage or deformation of the support part is not eligible for returns. ・The resin color of the product is subject to change without notice due to material procurement. ・Because the product is 3D modeled from photos and materials, please understand that the detailed dimensions may differ slightly from the actual tow bar before purchasing. ・The product contents are subject to change without notice. ・Because it is made of resin, please use instant adhesive instead of plastic adhesive. -Each part is supported by a support material (like a runner) connected to a base called a raft, so roughly separate the raft and support for each part, then carefully separate the support with a nipper or design knife. Please clean and assemble it. It usually takes less than 5 days to ship, but if you purchase a pre-ordered item at the same time, it will be shipped together with the pre-ordered item.